Skip to content
← Common Questions

Topping up · matching the material

Can you mix new sand with old sand?

Yes. Topping up is ordinary maintenance, and usually the right call.

Stripping an arena out is the rare and expensive exception.

So the question that decides the outcome is not whether you can mix. It is what you are mixing in.

the usual answer
A matched top-up, not a strip-out
what decides it
Grain size and shape. Not the mixing
the failure
One arena that rides as two surfaces

The short answer

Yes, and usually you should.

You can mix new arena sand with old, and topping up is usually the right call. What decides the outcome is whether the new material matches the grain size and shape of what is already down, not the mixing itself.

Sand leaves an arena constantly, so putting material back is maintenance rather than a rescue.

Whether the sand you have is finished is a different question, and when arena sand needs replacing answers that one. This page is about what to put in.

The part that goes wrong

What actually goes wrong.

Sand that behaves differently from what is already there does not blend into one surface.

It sorts itself out, and the arena ends up riding differently in different places.

None of that is caused by mixing. It is two materials with different habits sharing a floor.

A GOOD MATCHA MISMATCHTHEY NESTTHEY SEPARATEONE SURFACETWO SURFACES IN ONE ARENASOLID: WHAT IS ALREADY DOWN. LIGHTER: WHAT YOU ADD
The same existing grains on both sides. Only what was added changed.
01

Round grains travel

Add rounder sand to angular sand and the round grains move, rolling under a hoof instead of locking against their neighbors.

They bank up at the rail, where the riding is heaviest, while the middle carries on as it always did.

02

Fine material fills the gaps

Drop a finer material onto a coarser one and it works down into the spaces between the bigger grains.

Those spaces were doing a job.

Full up, the surface has nowhere to give. It is the same mechanism behind an arena that packs hard.

AS IT SITSAFTER A FINER TOP-UPSPACE BETWEEN THE GRAINSTHE SPACES ARE FULLTHE SURFACE CAN GIVENOWHERE LEFT TO GIVESAME GRAINS, SAME DEPTH. THE SPACES ARE WHAT CHANGED
The pile is the same height on both sides. Fine material bought no depth. It spent the space that let the surface give.

Match it against your own arena

Which top-ups work?

A top-up works when the new sand is close enough in size and edge shape to disappear into what is down.

It fails when it is not. Find what you have on the left, and what you are being offered next to it.

Common arena sand top-up pairings: what is already in the arena, what is being added, what happens to the surface, and whether to do it
What you already haveWhat you’re addingWhat happensDo it?
Sub-angular sand that rides well, just short of depthThe same material from the same sourceIt disappears into what is there. Depth comes back and the ride does not change.Yes
Angular sand that grips and holds its shapeA rounder sandRound grains travel. They get pushed to the rail and bank there, so the track goes loose while the middle stays put.No
Coarser sand with open space between the grainsA noticeably finer sandThe fine material works down into the voids and firms the surface up. Harder than either sand was alone.No
Sand worn round, but otherwise the right materialFresh, harder sand of the same size and shapeThe proportion of worn material drops and the surface improves. The worn grains are still in there.Yes, knowing that is what you are buying
Sand nobody can identifyAnythingUnknown until it is spread. You are guessing at size, shape and hardness, and the arena is where you find out.Not without checking
Material that was wrong for an arena from day oneMore of the right sandYou dilute the problem instead of removing it. The fines and the wrong shape are still in the arena.No. That is a different decision

Half the rows say no. In none of them is the mixing the problem. The match is.

There is an asymmetry worth knowing: going coarser is more forgiving than going finer.

Large grains stay where they are put. Fine material keeps working downward, and it does not come back up.

GOING COARSERGOING FINERIT SITS WHERE IT LANDSIT KEEPS WORKING DOWNWHERE YOU CAN SEE ITWHERE YOU CANNOT GET IT BACKONE MISTAKE STAYS ON TOP. THE OTHER GOES INTO THE BED.
The same bed on both sides. Coarser than the gaps, it stops at the surface; finer than the gaps, it threads straight past you.

Two sands that look identical in a bucket can behave nothing alike underfoot.

Grain shape decides two of those rows, and choosing arena sand sets out the four properties you are matching against.

Before a truck is booked

Check before you order.

You can settle this in advance by getting a sample of both materials and looking at them together.

Almost nobody publishes this part, and it is the part that changes the decision.

  1. STEP 01

    dig a sample of what you have

    Not off the top.

    Pull from below the surface in several places, including the track you ride most and the middle nobody uses.

    Mix them together before you look at anything.

  2. STEP 02

    ask for a sample of what is proposed

    From the pile your load would actually be dug out of.

    A sand name on a quote says what the material was graded for, not how it behaves next to yours.

  3. STEP 03

    put the two side by side, dry

    In daylight, on something pale.

    You are comparing two things: how big the grains are, and whether the edges are sharp, worn or rounded off.

  4. STEP 04

    settle both of them in jars

    Same jars, same water, same shake, read at the same time.

    Two jars side by side answer a comparison far better than one jar answers an absolute.

  5. STEP 05

    find out what the original material was

    Ask whoever spread it or built the arena, and check an old ticket.

    If that source still produces the same thing, it is the closest match you will get.

Step four is one procedure run twice. The settling jar test covers how to sample, shake and read a jar.

Do both materials at once and read them against each other.

Step five is worth doing first. If the original quarry still makes that material, going back to it is the easiest match anyone will hand you.

That points you at a pit rather than at us, and it is still the right advice.

The honest limit

When new sand won’t fix it.

There are two situations that look identical from the saddle and are not.

Good material that has worn down comes back with a top-up. Bad material does not come back at all.

If what is down is still the right sand and has simply been ridden thin, adding more of the same is maintenance and it works.

Sand that is only short of depth does not need removing. Do it when the surface asks for it and the arena keeps riding the way it should.

If what is down was wrong to begin with, new material on top of it does not fix it.

The same holds once sand has broken down past the point of being material you would choose to buy. You get a diluted version of the same problem.

The fines and the wrong grain shape do not leave when new material arrives.

You have changed the proportion, not the character.

Starting over costs more once; topping up bad material costs every time.

It is the one case where a strip-out earns what it costs.

If a top-up has been tried once and the surface settled straight back, the replacement decision covers how to read that pattern.

What a strip-out adds.

The decision is not really about the sand. It is about the work that comes with getting the old sand out.

THE SANDTHE FREIGHT TO MOVE ITSTRIPPING THE SURFACEHAULING THE OLD AWAYAN ARENA OUT OF USEA TOP-UPA REPLACEMENTEVERY TOP-UP JOB IS INSIDE EVERY REPLACEMENT JOB
Stripping out sound sand that is only short of depth pays for the whole list to arrive back where you started.
what a top-up is
The sand, and the freight to move it.
what a replacement adds
Stripping the surface, hauling the old material away, and an arena out of use meanwhile.
what moves both
Tons needed, distance to a suitable quarry, the truck your site can take, and whether the material has to be washed or screened.

Most answers to this question online are written by companies selling something to mix in.

Ours is about the sand matching the sand, and about being able to buy the same thing twice. A top-up is never a one-off.

Buying arena sand sets out the routes, including the local pit that is often the sensible one.

Asked before ordering

Mixing questions.

If yours isn’t here, give us a call and describe what is already down.

Yes, and it is how most arenas are kept up. It works as long as the new sand is close enough in size and shape to ride as one material with what is already down.

Usually not. Stripping out is the honest answer only when what is down was wrong for an arena to begin with, or has broken down so far that adding to it changes nothing.

You get a third surface, rarely the average of the two. Rounder grains travel and bank at the rail; the middle rides as it did. Finer grains work down into the voids between coarser ones and firm everything up.

Start with whoever supplied or built it: an old delivery ticket, the quarry, or a name on an invoice. If nobody knows, read the sand itself: dig below the surface, check grain size and edge shape, and settle a jar.

Topping up, in nearly every case, and it is not close. A top-up is sand and the freight to move it. A replacement is all of that plus stripping, hauling the old material away, and an arena out of use meanwhile.

No, and color is a poor test. Most of what you see is mineral content and staining on the grain surface. Size and edge shape decide how a surface rides; color only decides whether the top-up shows for a season.

Free quote · by phone

Tell us what’s already down.

Where the arena is, what you ride, and anything you know about the original load.

A ticket, a quarry, a name someone remembers. That is usually enough to say whether a matched top-up is available near you.

If your sand is fine, we will say that instead.

Call (704) 310-6238