Skip to content

Calculator · free, no email

How much sand does your arena need?

Put in your dimensions and the depth you ride on. You’ll get tons and truckloads.

One figure, at the trade’s flat rate of 100 lb per cubic foot, with every step shown. No form, no email.

what it gives you
Tons and truckloads, with the arithmetic
the rate it uses
100 lb per cubic foot, flat. No yards, no range
what it costs you
Nothing. No email, no sign-up

Your arena

What you'll need

250 tons of sand. 5,000 cubic feet. 12 to 14 truckloads.

tons of sand
truckloads
cubic feet
Riding surface
20,000 sq ft
Footing depth
3"
Volume
5,000 cu ft
Density, flat rate
100 lb / cu ft
Weight
500,000 lb

Tons = cubic feet × 100 lb ÷ 2,000, nothing added for settling · loads on a 18–22 ton truck

Footing layer only. Base, drainage and geotextile are a separate calculation.

The short answer

Depth moves it more than size does.

Length and width you already know. Depth is the one people guess at.

It multiplies straight through the arena, so one afternoon’s decision changes the tonnage meaningfully.

Work out depth first, from the discipline you ride. Run the tonnage second.

2" DEEPTONNAGE ×1.03" DEEPTONNAGE ×1.54" DEEPTONNAGE ×2.0

Same footprint, same base. Two inches to four doubles the tonnage.

Worked out for you

Common arena sizes.

The standard sizes at two, three and four inches. So you can see what an inch is worth.

Same arithmetic as the tool above, same flat rate. If they ever disagree, one of them is broken.

Tons of arena sand by arena size and footing depth, with truckload counts
Arena size2" deep3" deep4" deepLoads at 3"
20 × 40 mSmall dressage72tons108tons144tons5–7truckloads
20 × 60 mStandard dressage108tons163tons217tons8–10truckloads
60 × 120 ftPrivate arena60tons90tons120tons5truckloads
100 × 200 ftFull size167tons250tons333tons12–14truckloads
YOUR TOTAL TONNAGE…EACH LOAD 18–22 TONS

Tonnage becomes truckloads.

Load counts assume a truck and trailer carrying 18–22 tons per load.

Tighter sites take smaller rigs, and therefore more loads. See delivery and site access.

The math, in the open

Five steps, and you can check every one.

There is nothing proprietary in a tonnage calculation.

Here it is in full. Run it on the back of a feed bag and get the same answer.

DEPTH (INCHES)THE ONE THAT MULTIPLIESLENGTH (FEET)WIDTH (FEET)

Two dimensions in feet, one in inches. The small one multiplies.

20 CUBIC FEET2,000 LB · ONE TON12 IN1 CUBIC FOOT100 LB, FLAT RATE

Where ÷12 and ÷20 come from: twelve inches to the foot, 20 cubic feet to the ton.

  1. Step 01

    measure the riding surface

    Length and width in feet

    Measure what you ride on, not the fence line. The strip outside the track still costs a full truckload.

  2. Step 02

    pick your depth

    Inches, from the discipline table

    Depth matters more than either dimension, because it multiplies straight through. Half an inch across a full-size arena is real tonnage.

  3. Step 03

    work out the volume

    Length × width × depth ÷ 12

    Two dimensions in feet and one in inches. Dividing the inches by twelve gives cubic feet, the unit the weight comes from.

  4. Step 04

    turn cubic feet into tons

    Cubic feet × 100 lb ÷ 2,000

    Dry sand is figured at a flat 100 lb per cubic foot, so 20 cubic feet make a ton. One rate, no range, no yards.

  5. Step 05

    turn tons into truckloads

    Tons ÷ 18–22, rounded up

    A partial load is still a truck. The count is a range only because the rig that turns up is not fixed.

Every shape, in full

The formulas themselves.

Feet across, inches deep, tons out. The ÷240 is twelve inches to the foot, 100 lb to the cubic foot and 2,000 lb to the ton, folded into one number.

Rectangle
length × width × depth ÷ 240 = tons
Round pen
π × (diameter ÷ 2)² × depth ÷ 240 = tons
Oval
π × (across ÷ 2) × (long axis ÷ 2) × depth ÷ 240 = tons
Known area
area × depth ÷ 240 = tons
Then, every time
tons ÷ 18–22, rounded up = truckloads

Where the numbers come from

Depth method
Start shallow and add in half-inch steps, with a ceiling around six inches: Penn State Extension. The per-discipline ranges are our own working figures, not theirs.
Density, flat rate
100 lb per cubic foot of dry sand, the trade’s planning rate: 2,700 lb per cubic yard, about 1,602 kg/m³. The same default Omni Calculator’s sand calculator uses.
Settlement allowance
Optional. Published ordering guidance for arena sand adds fifteen to twenty percent; the calculator adds 15% only when you switch it on.
Truck capacity
18–22 tons is a planning figure for the rigs arena sand moves on. State weight limits and axle setup move it.

Optional

Sand settles. Order for it if you want to.

The depth off the truck is not quite the depth you ride on.

Sand goes down loose and beds in under hoof traffic and watering across the first few weeks. Published ordering guidance adds fifteen to twenty percent for it.

The calculator adds nothing for it unless you ask. Switch it on and it adds 15%, shown as its own line. Order three inches flat and you ride on about two and a half.

AS TIPPEDLOOSEAS RIDDENBEDDED INSETTLESWHAT ARRIVESWHAT YOU RIDE ONOPTIONAL: ADD 15% TO ORDER THE SETTLED DEPTH

The same sand twice: the volume that arrives, and the depth it becomes.

Read this before you order

One number. What still moves it.

The arithmetic is simple and exact, and the density is fixed.

Five things move the real figure once the sand is on a truck.

1 CUBIC FOOT, DRY100 LBTHE FLAT RATE2,700 LB PER CUBIC YARD20 CUBIC FEET TO THE TON

The one density in the chain, and what it is in each unit.

whether you order for settling

Sand goes down loose and beds in under traffic and watering. Published ordering guidance adds fifteen to twenty percent for it.

The calculator adds nothing unless you switch it on; then it adds 15% and shows the line.

Heavily ridden, heavily watered arenas settle hardest.

moisture on the weigh ticket

The flat rate is for dry sand. A damp load weighs more for the same volume, so a quarry ticket can read heavier than the arithmetic.

The volume your arena needs does not change. Buy by the ton and it is the ticket that moves, not the depth.

whether you are topping up or starting fresh

A new arena needs the full depth. A refresh needs only the difference between what you have and what you want.

Smaller, and much harder to eyeball. Measure what is there in several places before you order.

how level your base is

A base with dips takes more sand than the arithmetic suggests: the low spots fill first.

If the base is uneven, expect to order over the figure rather than under it.

what the truck can legally carry

Loads are capped by highway weight limits, not by what fits in the trailer.

Limits vary by state and axle configuration, so the load count is a planning estimate, not a booking.

Set your depth first

What depth should you run it at?

Depth follows the discipline. It is a soundness decision before it is a tonnage one.

Take the range for what you ride, then run it.

  • Dressage2"–3"

    Finer, sub-angular

  • Hunter / Jumper3"–4"

    Medium, sub-angular

  • Reining3"–5"

    Medium, over a firm base

  • Barrel Racing4"–5"

    Coarser, looser

  • Cutting4"–6"

    Coarse, deep

  • Roping3"–4"

    Medium

  • Trail / Pleasure2"–4"

    Medium, sub-angular

  • Multi-use3"–4"

    Medium, sub-angular

These are the working ranges we spec to, not a published standard. The method underneath them is Penn State Extension’s: start shallow, add in half-inch increments until it rides right.

Taking sand back out is far harder than putting more in, so the bottom of the range is the safer start.

Why each discipline sits where it does is covered on choosing your sand.

Asked every week

Tonnage questions.

Not sure which number to trust? Give us a call with your dimensions.

A 20 × 40 meter arena at 3 inches deep is 108 tons. Set the calculator to that preset for your own depth. The table below shows the same sizes at two, three and four inches.

Multiply length by width by depth in inches, then divide by 240. That is the whole formula: divide by twelve for the inches, multiply by 100 lb per cubic foot, divide by 2,000 for tons. The calculator runs exactly that and shows each step.

All three. Round takes a diameter, oval takes both axes, and for a top-up you set what is already down so only the difference gets ordered. An arena already at depth returns nothing to buy.

Yes. Choose to enter the area instead of the dimensions, in square feet or square meters. If you have measured an irregular arena yourself, that beats anything we could work out from two sides.

Yes. Switch the units and dimensions read in meters, depth in centimeters, volume in cubic meters, density as 1,602 kg/m³. The arithmetic is unchanged, so the tonnage is identical. Tons are US short tons of 2,000 lb, the trade's unit.

It is the trade's planning rate for dry sand: 2,700 lb per cubic yard, 20 cubic feet to the ton. One rate keeps every figure comparable with your next quote. A damp load weighs more on the ticket; the volume you need does not.

Divide the cubic feet by 27. At the flat rate a cubic yard weighs 2,700 lb, or 1.35 tons, so tons ÷ 1.35 gives yards. The calculator works in tons because that is how bulk sand is sold and hauled.

Most bulk arena sand moves on a truck and trailer carrying roughly 18 to 22 tons per load, which is why almost every arena takes several loads. Smaller rigs carry considerably less and are used where access is tight.

The tonnage is fixed arithmetic at one flat density, so it is one figure. The load count divides it by what a truck carries, roughly 18 to 22 tons, and the rig that turns up depends on your site.

Nothing is added for settling unless you switch it on, which adds 15% and shows the line. Beyond that it is your base: dips fill first and take more than the arithmetic says. One extra delivery often costs more than ordering high.

Just the sand, meaning the footing layer only. Base material, drainage and geotextile are separate from what we do and from this arithmetic. Building from scratch? Specify and build the base first.

No. No gate, no download, no form. Run it as many times as you like. To talk through what the numbers mean for your arena, the phone number is at the bottom of the page.

Yes, with credit. The address updates as you work, so copy the link and it reopens on exactly the numbers you ran. No permission needed. We would rather be quoted accurately than not at all.

Got your tonnage? What drives arena sand cost explains what sets the figure. Delivery and site access covers what a loaded truck needs to reach you.

Free quote · by phone

Got a number. Now what?

Call and read us the figure. We’ll tell you whether it looks right for the arena you’re describing.

Then what sand suits how you ride, and what it takes to get it to your address. If your tonnage looks off, we’ll say so.

Call (704) 310-6238